Porsche Boxster / Cayman S 3.4 ECU Tuning – MA1 Optimized Performance | 987.2 2009–2012

This isn't a generic flash. Our 987.2 Boxster S and Cayman S 3.4 calibrations are developed in-house, optimized on the dyno, and tested on the street and track. Every map is built around your fuel, your hardware and how you actually drive the car — real gains with factory-level refinement and reliability.

Estimated on a healthy car with known-good fuel:

• 306 hp → 335 hp — estimated gain of +29 hp
• 251 lb-ft → 285 lb-ft — estimated gain of +34 lb-ft
• Fuel maps available for 91, 93 and 100 octane
• Sharper throttle response and revised rev limits
• Calibrated for consistent performance in all conditions

The 987.2 Boxster S and Cayman S run the MA1 3.4L direct-injection naturally aspirated flat-six, and this is the strongest naturally aspirated result in our entire range — +29 hp and +34 lb-ft, with the torque gain exceeding the horsepower gain. Direct injection gives the calibration far finer control over fuelling and knock margin than the earlier port-injected cars, and it shows. The MA1 engine also resolved the intermediate shaft bearing issue that shadows the earlier M96 and M97 cars.

What's included:

• Custom MA1 ECU calibration developed around your fuel, hardware and driving preference
• Optimized ignition timing, fuelling and rev limits for your specific car
• Throttle response and drivability refinement
• Fuel map matched to the octane you actually run — 91, 93 or 100
• OBDII data cable shipped to you
• Same-day file turnaround once we have your stock read

What we need from you:

• Your factory stock file, read with the cable we send you
• A complete list of current modifications
• Vehicle details and VIN
• An honest description of the car's mechanical condition and service history
• The octane you run day to day

Supported Vehicles:

• Porsche Boxster S (987.2) — 3.4L direct-injection naturally aspirated flat-six, MA1, 2009–2012
• Porsche Cayman S (987.2) — 3.4L direct-injection naturally aspirated flat-six, MA1, 2009–2012

How to order:

• 1. Order online. We ship you an OBDII data cable — typically 2–3 days to arrive.
• 2. Read your stock file. Plug the cable into your OBD port, upload your factory file, then email it to us with a list of your current modifications.
• 3. Get your file back the same day. We email your custom calibration back the day we receive your stock read — and we'll make sure you're happy with it.

In the Southern California area? Get in touch and we can tune your car in person instead.

Before you order:

• Power figures are estimates, not guarantees. Results vary with fuel quality, altitude, ambient temperature, mechanical condition, supporting modifications and dyno methodology.
• Mechanical condition — tuning raises cylinder pressure and driveline load. The car must be sound first. Pre-existing faults revealed or accelerated by tuning are not our responsibility.
• Accurate information required — we build the file from what you tell us. An unmodified stock read and an honest description of the car, its modifications and its condition are required.
• Warranty — an ECU modification will likely void any remaining factory powertrain warranty.
• Legal use — certain calibrations are for off-road and competition use only. Compliance with federal, state and local emissions law is the buyer's responsibility.
• Risk and liability — the customer assumes the risk of modification. Our liability is limited to the price of the tuning service.

Note: Tuning services are non-refundable once the file has been delivered. The service is complete at delivery. Full terms are on our Terms of Service page.

Questions about your specific car? Get in touch — we're happy to confirm the right calibration before you order.

FlatSixSpirit — Premium Porsche Performance Parts
Remote Delivery · Custom Calibration